Project 12
How to make a sheet metal box in SOLIDWORKS
A sheet metal box is the standard fabrication project: one base flange, four edge flanges, closed corners and a flat pattern for the laser. With 1.5 mm steel, a 1.5 mm bend radius and K = 0.5, you can check the flat blank by hand before the shop cuts it.

- Level
- Project
- Time
- 40 min
- Material
- Mild steel, 7.85 g/cm³
Specification
| Parameter | Value |
|---|---|
| Material / thickness | Steel, 1.5 mm |
| Bend radius / K-factor | 1.5 mm / 0.5 |
| Outside size | 200 × 150 × 50 mm |
| Bend deduction per 90° bend | 2.466 mm |
| Flat blank (bounding box) | 295.07 × 245.07 mm |
The key dimensions

Step by step
1. Base flange
200 × 150 rectangle, thickness 1.5, radius 1.5, K-factor 0.5.
2. Edge flanges
Four edge flanges 50 mm, measured to the outer virtual sharp, material inside.
3. Corners
Closed Corner with a small gap, or keep relief cuts for an open corner box.
4. Flat pattern
Flatten and read the bounding box in the cut list properties.
5. Export
Right-click the flat pattern → Export to DXF/DWG, geometry only, 1:1.
Check your result
- Flat blank 295.07 × 245.07 mm (200 + 2 × 50 − 2 × 2.466 by 150 + 2 × 50 − 2 × 2.466).
- Confirm the bend deduction in the K-factor calculator.
This project has no download: the numbers above are the check. Build it from the specification and compare.
Next: project 13 — spur gearbox.
Commands used
Show solution
- Base flange. 200 × 150 rectangle, thickness 1.5, radius 1.5, K-factor 0.5.
- Edge flanges. Four edge flanges 50 mm, measured to the outer virtual sharp, material inside.
- Corners. Closed Corner with a small gap, or keep relief cuts for an open corner box.
- Flat pattern. Flatten and read the bounding box in the cut list properties.
- Export. Right-click the flat pattern → Export to DXF/DWG, geometry only, 1:1.
Sources
- GoEngineer — SOLIDWORKS sheet metal bend calculations explained (May 2022)
- Javelin — Calculating bend allowance, bend deduction and K-factor (Jun 2017)
- Javelin — What are bend allowance, bend deduction and K-factor? (Jun 2017)
- SOLIDWORKS Help 2024 — Flat-Pattern PropertyManager
- SOLIDWORKS Help 2024 — Closed corners
- GoEngineer — Export flat pattern to DXF (Jul 2024)
Checked November 2026. SOLID WORKS Club is independent; menu names can differ slightly between releases.
Frequently asked questions
How do I calculate the flat size of a sheet metal box?
+
Add the outside dimensions of base and flanges and subtract one bend deduction per bend: BD = 2·OSSB − BA.
Which K-factor should I use?
+
Your fabricator's value. K = 0.5 is SOLIDWORKS' default and is used here so the check is easy to repeat.
Related
- How to design a simple gearbox in SOLIDWORKSDesign a 2:1 spur gearbox in SOLIDWORKS: module 2 gears with 20 and 40 teeth, 60 mm centre distance, housing, shafts, gear mate and interference check.
- How to design a 3D-printed enclosure in SOLIDWORKSDesign a 3D-printed electronics enclosure in SOLIDWORKS: 2 mm walls, a lid with a locating lip and 0.3 mm clearance, snap-fit rules, and STL or 3MF export.
- Base Flange — the first sheet metal featureStart a SOLIDWORKS sheet metal part with Base Flange/Tab: open and closed profiles, thickness, bend radius, K-factor, gauge tables and auto relief.
- Intermediate SOLIDWORKS exercises19 intermediate SOLIDWORKS exercises: sweeps, lofts, shells, draft, Hole Wizard and three small assemblies, each with a drawing, STEP file and check mass.