Skip to content
SOLID WORKS ClubSOLID WORKS Club

Assemblies · Lesson 2

SOLIDWORKS standard mates

Mates are the 3D version of sketch relations: they tell SOLIDWORKS how two components sit against each other. The eight standard mates — Coincident, Parallel, Perpendicular, Tangent, Concentric, Lock, Distance and Angle — position almost everything. The fastest way to add one is to Ctrl-select two faces or edges and pick the mate from the Quick Mates toolbar that appears.

Kevin Walsh Kevin Walsh Updated Checked for SOLIDWORKS 2026
Eight small diagrams of coincident, parallel, perpendicular, tangent, concentric, lock, distance and angle mates

Where to find it

Assembly tab → Mate (paperclip); or Ctrl-select two entities for Quick Mates

The standard mates

Mate Result Typical selections
Coincident Faces, edges or points touch or lie in one plane Face to face, plane to plane
Parallel Faces or edges stay parallel Two planar faces
Perpendicular 90° between faces or edges Two planar faces
Tangent Round face touches a flat or round face Cylinder to plane
Concentric Common axis Pin to hole
Lock Fixes two components together Any two components
Distance Set gap Two faces
Angle Set angle Two faces or edges

Version notes

Version Change
2014 Quick Mates toolbar; lock rotation on concentric mates
2016 Mate Controller to save and animate mate positions
2020 Slot, Profile Center, Width and limit mates on Quick Mates
2021 Mate PropertyManager reorganised into tabs: Standard, Advanced, Analysis, Mechanical
2022 Alignment and lock rotation buttons on Quick Mates

When mates conflict, see mate errors. More mate types: advanced mates.

Practise mates with a check value: the spacer stack, bracket pair and shaft in pillow blocks assemblies.

Step by step

  1. 1

    Open the pin assembly

    Use the plate-and-pins assembly from the previous lesson.

  2. 2

    Concentric pin and hole

    Hold Ctrl and click the cylindrical face of a pin and the inside face of a hole. On the Quick Mates toolbar choose Concentric. The pin jumps into line with the hole.

    Quick Mates toolbar after Ctrl-selecting a pin face and a hole face, with Concentric highlighted
    Ctrl-select two faces and pick the mate from the Quick Mates toolbar.
  3. 3

    Set the depth with Coincident

    Ctrl-select the pin's end face and the bottom face of the plate, choose Coincident. If the pin flips the wrong way, change the alignment (Aligned / Anti-Aligned) or press Tab.

  4. 4

    Lock the spin (optional)

    The pin can still spin about its axis — it shows (-). Edit the concentric mate and tick Lock rotation, or leave it free if it should turn. Repeat for the second pin.

Common mistakes

  • Wrong alignment — the part flips to the other side. Toggle Aligned / Anti-Aligned or press Tab.
  • A face hidden behind others. Hold Alt over it to hide it temporarily and select what is behind.
  • Adding more mates than needed, which over defines the assembly. Each degree of freedom needs one mate.
  • Using a distance mate where coincident would do, which makes the assembly harder to change.

Lesson 2 of 16 in the assemblies course.

Practice

Mate both pins concentric with their holes and coincident with the bottom face of the plate. Check: each pin sticks out 20 mm above the plate's top face — measure from the top face to the pin end with Evaluate → Measure. With lock rotation on, the pins lose their (-).

Sources

Checked November 2026. SOLID WORKS Club is independent; menu names can differ slightly between releases.

Frequently asked questions

What are the standard mates in SOLIDWORKS?

+

Coincident, Parallel, Perpendicular, Tangent, Concentric, Lock, Distance and Angle.

What is the fastest way to add a mate?

+

Ctrl-select the two entities; the Quick Mates toolbar appears next to the pointer and suggests suitable mates. It has existed since SOLIDWORKS 2014.

How do I flip a mate?

+

Change the alignment between Aligned and Anti-Aligned, press Tab while mating, or right-click the mate and choose Flip Mate Alignment.

How do I stop a pin from spinning?

+

Tick Lock rotation on the concentric mate (available since 2014). You can lock all concentric mates at once from the right-click menu of the Mates folder.