Assemblies · Lesson 4
SOLIDWORKS mechanical mates
Mechanical mates describe how mechanisms move: gears turning each other, a cam pushing a follower, a screw driving a nut, a hinge swinging a lid. They link the motion of components by a rule or ratio, so when you drag one part the others follow. They do not check that gear teeth actually mesh — they apply the ratio you set.

Where to find it
Mate PropertyManager → Mechanical tab
Mechanical mates
| Mate | Links | Typical use |
|---|---|---|
| Cam | Follower to a closed loop of tangent faces | Cams, eccentrics |
| Slot | Pin or axis in a slot | Slotted links, adjusters |
| Hinge | Concentric + coincident, optional angle limits | Doors, lids |
| Gear | Rotation by ratio, with Reverse | Gear trains, pulleys |
| Rack Pinion | Linear travel of a rack to rotation of a pinion | Rack drives |
| Screw | Rotation to linear travel | Lead screws, jacks |
| Universal Joint | Rotation between two shafts at an angle | Drive shafts |
From SolidProfessor's guide to mechanical mates. Since 2021 they sit on the Mechanical tab of the Mate PropertyManager. For motion with time, forces and gravity, the Motion Study tools are covered in a later course.
Practise it: the gear mate in the gearbox project, the screw mate in the bench vise and hinge mates in the robot arm.
Step by step
-
1
Make two discs
Model two discs as stand-ins for gears: Ø80 and Ø40, each 10 mm thick with a Ø10 centre hole. Insert a base plate with two pins 60 mm apart and mount the discs concentric on the pins.
-
2
Add a Gear mate
Mate → Mechanical → Gear. Select a circular edge of each disc. Set the ratio to 80 : 40 (SOLIDWORKS suggests one from the sizes). Tick Reverse if they turn the same way.

The gear mate links rotation by the ratio you set. -
3
Test it
Drag the large disc: the small one turns twice as far in the opposite direction.
Common mistakes
- Expecting the gear mate to check tooth contact — it only applies the ratio.
- Forgetting the concentric mates that hold each gear on its axis; the gear mate only links rotation.
- A cam profile that is not one closed loop of tangent faces — the cam mate needs that.
Lesson 4 of 16 in the assemblies course.
Practice
Link the Ø80 and Ø40 discs with a 2 : 1 gear mate. Check: rotate the large disc by 90° with Rotate Component (by delta) — the small disc turns 180° the other way.
Sources
- SolidProfessor — Mechanical assembly mates (2019)
- GoEngineer — Introduction to SOLIDWORKS mates (Feb 2022)
- SOLIDWORKS blog — New assembly productivity tools in 2021
Checked November 2026. SOLID WORKS Club is independent; menu names can differ slightly between releases.
Frequently asked questions
How does the gear mate work?
+
It links the rotation of two components by a ratio, based on the sizes you select or a value you enter. It does not use the actual tooth geometry.
What is the screw mate for?
+
It combines a concentric constraint with a link between rotation and linear travel, like a lead screw driving a nut.
What does a hinge mate do?
+
It combines concentric and coincident in one mate and can limit the swing angle.
What is a cam mate?
+
A mate that keeps a follower in contact with a closed loop of tangent faces, so the follower moves as the cam turns.
Related
- SOLIDWORKS advanced matesHow to use SOLIDWORKS advanced mates: Profile Center, Symmetric, Width, Path, Linear/Linear Coupler, and distance and angle limit mates for ranges of motion.
- SOLIDWORKS standard matesHow to use SOLIDWORKS standard mates: coincident, parallel, perpendicular, tangent, concentric, lock, distance and angle, Quick Mates and lock rotation.
- Component patterns and Mirror ComponentsHow to pattern components in SOLIDWORKS assemblies: linear, circular, pattern driven and chain patterns, plus Mirror Components and opposite hands.
- SOLIDWORKS mate errors — over defined and failed matesFix SOLIDWORKS mate errors: over defined components, mates not satisfied, conflicting mates and fixed parts, using MateXpert and the Mates folder.