Project 6
How to model a ball bearing in SOLIDWORKS
A deep groove ball bearing is a small assembly: an inner ring, an outer ring and a set of balls in raceway grooves. This project uses the 6201 — 12 mm bore, 32 mm outside, 10 mm wide — with seven 5.953 mm balls as listed by NSK. The ring cross-sections are simplified; the envelope and balls follow the manufacturer's data, which is what matters in an assembly.

- Level
- Project
- Time
- 40 min
- Material
- Mild steel, 7.85 g/cm³
- Check mass
- 36.26 g total
Specification
| Parameter | Value |
|---|---|
| Bore d | 12 mm |
| Outside diameter D | 32 mm |
| Width B | 10 mm |
| Balls | 7 × Ø5.953 mm (NSK) |
| Ball pitch circle | Ø22 (our choice) |
| Rings | Simplified: inner Ø12–Ø18.4, outer Ø25.6–Ø32 |
The drawing
Step by step
1. Rings
Revolve each ring's cross-section; cut a raceway groove slightly larger than the ball radius in both rings on the Ø22 pitch circle.
2. One ball
A sphere Ø5.953 centred on the pitch circle at mid-width — revolve a half circle or use a separate part.
3. Pattern the balls
In an assembly, Circular Component Pattern of 7 around the bearing axis.
4. Mates
Concentric rings and balls on the axis; Coincident mid-planes. Leave the outer ring free to rotate for motion studies.
5. Or use Toolbox
Toolbox includes bearings, and supplier sets such as SKF are part of its content.
Check your result
- Envelope 12 × 32 × 10 mm.
- 7 balls of Ø5.953.
- Our simplified STEP assembly weighs 36.26 g in steel at 7.85 g/cm³.
Compare your model with the STEP file above — it opens in SOLIDWORKS and most other CAD programs.
Download files
Commands used
Show solution
- Rings. Revolve each ring's cross-section; cut a raceway groove slightly larger than the ball radius in both rings on the Ø22 pitch circle.
- One ball. A sphere Ø5.953 centred on the pitch circle at mid-width — revolve a half circle or use a separate part.
- Pattern the balls. In an assembly, Circular Component Pattern of 7 around the bearing axis.
- Mates. Concentric rings and balls on the axis; Coincident mid-planes. Leave the outer ring free to rotate for motion studies.
- Or use Toolbox. Toolbox includes bearings, and supplier sets such as SKF are part of its content.
Sources
- NSK — 6201 deep groove ball bearing
- igus — Deep groove ball bearing dimension table
- Hawk Ridge — Automating fasteners with Toolbox (Aug 2023)
- UPenn MEAM.Design — SolidWorks: the Design Library
Checked November 2026. SOLID WORKS Club is independent; menu names can differ slightly between releases.
Frequently asked questions
What does 6201 mean?
+
In the 62 series the last two digits are a bore code: 00 = 10 mm, 01 = 12 mm, 02 = 15 mm, 03 = 17 mm. The 6201 is 12 × 32 × 10 mm.
Should I model bearings myself?
+
For assemblies, use Toolbox or a supplier model. Model your own only to learn or when you need a simplified envelope.
Related
- How to design a chair in SOLIDWORKSDesign a chair in SOLIDWORKS: weldment frame from 25 mm square tube, seat at 450 mm, seat board, cut list and mass, with ergonomic sizes from design guides.
- How to model a bolt and nut in SOLIDWORKSModel an ISO 4017 M10 bolt and ISO 4032 nut in SOLIDWORKS: hexagon sizes from the standard, chamfers, cosmetic or physical threads, and Toolbox fasteners.
- SOLIDWORKS RevolveHow to use Revolved Boss/Base and Revolved Cut in SOLIDWORKS: sketch half a profile, choose the axis, set the angle and fix open-sketch errors.
- Intermediate SOLIDWORKS exercises19 intermediate SOLIDWORKS exercises: sweeps, lofts, shells, draft, Hole Wizard and three small assemblies, each with a drawing, STEP file and check mass.