Errors & Fixes
SOLIDWORKS Simulation mesh failed — how to fix it
A mesh fails when the mesher cannot fill some part of the geometry with valid elements. GoEngineer boils it down to three causes: bodies that interfere, an element size larger than a face or feature, and parts that need an incompatible mesh. Small faces and bad imported geometry make up most of the rest. Failure Diagnostics shows you which body failed — start there.

Applies to: SOLIDWORKS Simulation 2020–2027 (Standard, Professional, Premium).
Most likely causes
- Element size larger than a small face, edge or feature (most common)
- Interfering bodies with bonded global contact (common)
- Sliver faces, short edges, knife edges in imported geometry (common)
- Assemblies that need an incompatible mesh (occasional)
- Element size so small that memory runs out (occasional)
Fix order

- Failure Diagnostics — which body failed?
- Mesh it alone, reduce the size until it meshes.
- Put that size in a mesh control on the original study.
- Still failing? Curvature-based or blended mesh.
- Several bodies? Check interference and contact.
- Last: simplify or repair the geometry.
Too small is also a problem
Shrinking the global element size until everything meshes works, but GoEngineer warns that a very small size can run out of memory or make the solve very long. Local mesh controls refine only where needed. Since SOLIDWORKS 2021 the blended curvature-based mesher is multi-threaded, according to PLM Group.
How meshes, element sizes and quality work is explained in the mesh lesson; setting up a first study is in static study. Imported parts with bad faces: repair them first with import errors.
Fixes, in order
1. Open Failure Diagnostics
Click it in the Mesh creation failed dialog, or right-click Mesh → Failure Diagnostics. Failed bodies are listed in the Simulation Advisor; Show bodies which failed to mesh highlights them, and clicking one fills the mesh control selection.
2. Apply a mesh control
Right-click Mesh → Apply Mesh Control on the failed body, face or edge and set a smaller Element size and growth ratio. To find a size that works, mesh that part alone in its own study first.
3. Switch to a curvature-based mesh
The standard mesher tries one element size everywhere, so small faces break it. Curvature-based mesh shrinks elements around holes and curves; Hawk Ridge calls it the usual default. Blended curvature-based is the heavier tool for hard parts.
4. Resolve interfering bodies
With bonded global contact, overlapping bodies make the mesher merge nodes into bad elements. Remove the overlap (find it with Interference Detection) or set global contact to Allow Penetration or No Penetration and define local contact sets.
5. Remesh failed parts with an incompatible mesh
In Create Mesh → Advanced, Remesh failed parts with incompatible mesh lets each part mesh on its own. GoEngineer then sets the study's bonding option to the more accurate setting.
6. Simplify the geometry
Suppress cosmetic fillets, chamfers, logos and small holes that do not matter to the result. Simplify Model for Meshing (right-click Mesh) can do it in a derived configuration.
7. Find and remove bad geometry
Check finds invalid faces and edges; Geometry Analysis finds sliver faces, short edges and knife edges. Delete and patch them, or split a complex part to find the area that fails.
8. Use draft quality only to test
Draft quality meshes faster with first-order elements — useful to check a setup, not for final results. Keep at least two elements through thin walls.
Sources
- GoEngineer — Fix Failed Mesh in SOLIDWORKS Simulation (Nov 2017)
- GoEngineer — Solving Mesh Failures in SOLIDWORKS Simulation with Mesh Controls (Apr 2022)
- Javelin — Resolving Mesh Failures and Errors in SOLIDWORKS Simulation (Oct 2021)
- SOLIDWORKS Tech Blog — Handling Interferences for Meshing in SOLIDWORKS Simulation (Jun 2019)
- Hawk Ridge Systems — Ins and Outs on Meshing Elements for SOLIDWORKS Simulation (Aug 2018)
- PLM Group Support — Why is my mesh failing?
- CATI — Mesh Failure Diagnostics, Part 2 (May 2011)
Checked November 2026. SOLID WORKS Club is independent; menu names can differ slightly between releases.
Frequently asked questions
Why does my SOLIDWORKS Simulation mesh fail?
+
Usually because the element size is too large for a small face or feature, bodies interfere, or the geometry has bad faces. Failure Diagnostics shows which body failed.
What element size should I use?
+
Mesh the failed part alone and reduce the size until it meshes, then use that size in a mesh control on the original study. Hawk Ridge's rule of thumb is at least two elements across thin walls and around fillets.
What is the difference between standard and curvature-based mesh?
+
The standard mesher uses one element size throughout; curvature-based mesh makes elements smaller around holes and curved faces, so it copes with small features better.
Related
- Meshing in SOLIDWORKS SimulationSOLIDWORKS Simulation meshing: blended curvature-based mesher, density slider, mesh controls, draft vs high quality elements, aspect ratio, convergence.
- Your first static studyRun your first SOLIDWORKS static study: add-in, material, fixtures, loads, contacts, mesh and run, then check the deflection against beam theory.
- SOLIDWORKS Interference DetectionHow to use Interference Detection in SOLIDWORKS: overlaps and their volume, ignoring and isolating results, Clearance Verification and Hole Alignment.
- SOLIDWORKS STEP and IGES import errors — how to fix themFix SOLIDWORKS STEP and IGES import errors: faulty faces and gaps, surfaces instead of solids, 3D Interconnect vs classic import, wrong IGES units.